Priručnik Hikoki DV 16V Udarna bušilica

Priručnik

4

English

APPLICATIONS

○ By combined actions of ROTATION and IMPACT:

Boring holes in hard materials (concrete, marble, granite,

tiles, etc.)

○ By ROTATIONAL action:

Boring holes in metal, wood and plastic.

SPECIFICATIONS

Voltage (by areas)* (110 V, 220 V, 230 V, 240 V)

Power input 590 W*

No load speed 0 – 2900 min

-1

Drill chuck capacity 13 mm

Capacity

Steel

13 mm

Concrete

16 mm

Wood

25 mm

Full-load impact rate

34500 min

-1

Weight (without cord) 1.5 kg

* Be sure to check the nameplate on product as it is subject

to change by areas.

NOTE

Due to HiKOKI’s continuing program of research and

development, the specifi cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Fixing and removing side handle

199

Using depth stopper 2 99

Mounting and dismounting of

the bit

399

Dismounting the bit of keyless

chuck (When the keyless chuck

cannot be loosened)

499

Selecting rotation direction 5 100

Selecting the operating mode 6 100

Switch operation

7 100

Locking-on the switch

8 100

Releasing the switch

9 100

Mounting position of hook (A)*

(Optional accessory)

10 100

Selecting accessories ― 101

* Attaching the hook. (Optional accessory) (Fig. 10)

(1) To attach the hook, it is necessary to disassemble

the handle portion which covered the tool’s electrical

system. For your continued safety and electrical

shock protection, installing the hook on this impact

drill should ONLY be performed by a HiKOKI

AUTHORIZED SERVICE CENTER.

(2) When the power tool is used with a hook fixed to it,

pay attention to the following points:

○ Before hanging the main unit from the waist belt, make

sure that the impact drill has come to a complete stop.

While it is suspended from the waist belt, the power

plug must be disconnected from the power source.

○ Do not walk about with the power tool hanging from

the waist belt.

○ In the case of operation in a high place, it is dangerous

to drop the tool accidentally. If the hook is deformed or

hung from the wrong position, there is danger that the

hook will slip off and the tool will fall.

Be careful to avoid danger.

○ In making a through hole, the power tool sometimes

shakes violently when the workpiece is pierced, from

example. Be careful you are not hurt by the hook even

if such situation happens.

Selecting the appropriate drill bit

○ When boring concrete or stone

Use the drill bits specifi ed in the Optional Accessories.

○ When boring metal or plastic

Use an ordinary metalworking drill bit.

○ When boring wood

Use ordinary woodworking drill bit.

However, when drilling 6.5 mm or smaller holes, use a

metalworking drill bit.

MAINTENANCE AND INSPECTION

1. Inspecting the drill bits

Since use of an abraded drill bits will cause motor

malfunctioning and degraded effi ciency, replace the drill

bits with a new one or resharpening without delay when

abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock protection,

carbon brush inspection and replacement on this tool

should ONLY be performed by a HiKOKI Authorized

Service Center.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country specifi c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

0000Book̲DV16V.indb40000Book̲DV16V.indb4 2017/12/0410:27:242017/12/0410:27:24

Ocjena

Više o ovom priručniku

Razumijemo da je lijepo imati papirnati priručnik za svoj Hikoki DV 16V Udarna bušilica. Uvijek možete preuzeti priručnik s naše web stranice i sami ga ispisati. Ako želite imati originalni priručnik, preporučujemo da kontaktirate Hikoki. Oni bi mogli osigurati originalni priručnik. Tražite li priručnik za svoj Hikoki DV 16V Udarna bušilica na drugom jeziku? Odaberite željeni jezik na našoj početnoj stranici i potražite broj modela da vidite imamo li ga na raspolaganju.

Tehnički podaci

Svi priručnici za Hikoki Udarne bušilice
Više priručnika za Udarne bušilice

Često postavljana pitanja o Hikoki DV 16V Udarna bušilica

Naš tim za podršku pretražuje korisne informacije o proizvodu i odgovore na česta pitanja. Ako u častim pitanjima naiđete na netočne informacije, obratite nam se putem obrasca za kontakt.

Povezani proizvodi

Priručnik

Hikoki DV 20VD Udarna bušilica

Priručnik

Hikoki D 13VL Udarna bušilica

Priručnik

Hikoki DV 22V Udarna bušilica

Priručnik

Hikoki DV 13SS Udarna bušilica

Priručnik

Hikoki DV 20VB2 Udarna bušilica

Priručnik

Hikoki D 13VB3 Udarna bušilica

Priručnik

Milwaukee HDE 13 RQD Udarna bušilica

Priručnik

AEG Pneumatic 2000 R Udarna bušilica

Povezane kategorije