Priručnik Hikoki G 23BYE Kutna brusilica

Priručnik

10

English

MAINTENANCE AND INSPECTION

1. Inspecting the depressed center wheel

Ensure that the depressed center wheel is free of cracks

and surface defects.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Replacing supply cord

If the replacement of the supply cord is necessary, it

has to be done by HiKOKI Authorized Service Center to

avoid a safety hazard.

4. Maintenance of the motor

WARNING

Always wear protective goggles and dust respirators

when blowing air from the tail cover air hole with the use

of an air gun, etc.

Failure to observe this may result in ejected dust being

inhaled or entering your eyes.

The motor unit winding is the very “heart” of the power tool.

Exercise due care to ensure the winding does not become

damaged and/or wet with oil or water.

NOTE

When work has been fi nished, blow air containing no

moisture from the tail cover air hole with the use of an

air gun, etc., while running the motor without any load

applied. This is eff ective in removing any dirt and dust

that has accumulated. Dirt and dust collecting inside the

motor may result in malfunctions.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country specifi c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this tool may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 99.5 dB (A).

Measured A-weighted sound pressure level: 88.5 dB (A).

Uncertainty K: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN60745.

Surface grinding:

Vibration emission value

a

h

,

AG

= 10.3 m/s

2

Uncertainty K = 1.5 m/s

2

The declared vibration total value has been measured in

accordance with a standard test method and may be used

for comparing one tool with another.

It may also be used in a preliminary assessment of exposure.

WARNING

○ The vibration emission during actual use of the power

tool can diff er from the declared total value depending in

the ways in which the tool is used.

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time).

NOTE

Due to HiKOKI’s continuing program of research and

development, the specifi cations herein are subject to

change without prior notice.

0000Book̲G23BYE.indb100000Book̲G23BYE.indb10 2019/02/279:27:212019/02/279:27:21

Ocjena

Više o ovom priručniku

Razumijemo da je lijepo imati papirnati priručnik za svoj Hikoki G 23BYE Kutna brusilica. Uvijek možete preuzeti priručnik s naše web stranice i sami ga ispisati. Ako želite imati originalni priručnik, preporučujemo da kontaktirate Hikoki. Oni bi mogli osigurati originalni priručnik. Tražite li priručnik za svoj Hikoki G 23BYE Kutna brusilica na drugom jeziku? Odaberite željeni jezik na našoj početnoj stranici i potražite broj modela da vidite imamo li ga na raspolaganju.

Tehnički podaci

Svi priručnici za Hikoki Kutne brusilice
Više priručnika za Kutne brusilice

Često postavljana pitanja o Hikoki G 23BYE Kutna brusilica

Naš tim za podršku pretražuje korisne informacije o proizvodu i odgovore na česta pitanja. Ako u častim pitanjima naiđete na netočne informacije, obratite nam se putem obrasca za kontakt.

Povezani proizvodi

Priručnik

Hikoki G 23SWU2 Kutna brusilica

Priručnik

Hikoki G 18UDY Kutna brusilica

Priručnik

Hikoki G 12VA Kutna brusilica

Priručnik

Hikoki G 14DBL Kutna brusilica

Priručnik

Hikoki G 3613DA Kutna brusilica

Priručnik

Hikoki G 10SQ2 Kutna brusilica

Priručnik

Hikoki G 10SN Kutna brusilica

Priručnik

Hikoki G 13VE Kutna brusilica

Povezane kategorije