Priručnik SilverCrest IAN 281169 Stroj za vakuumiranje

Priručnik

7

GB

7. Preparation

7.1 Setting up the device

Place the device on a dry, level and heat-re-

sistant surface.

7.2 Requirements on the

film/bags

- You can use tubular film or complete

bags.

- The film must not be wider than 28 cm.

- The film must be provided with dots/

knobs or grooves on one side. Smooth

films are not suited for sealing.

- Thickness should be between 0.17 and

0.29 mm (170 - 290 ).

- When buying the film, check the temper-

ature range it is suited for. The ideal

range is between -20 °C and +110|°C.

Such films can be deep-frozen or boiled.

The film included in the delivery is suited

for this application.

- You will find those data on the package

of the film or bag.

7.3 Producing a bag

If you use finished bags, these steps do not

apply.

1. Unwind the length of film from the roll

you require for your bag. Regarding the

length of the bag, remember that a

space of approx. 6 cm towards the top

should be left after filling.

2. Use scissors to cut the piece of film as

straight as possible.

3. For sealing the bag (see “Seal the bag”

on page 7).

8. Use

Every active function can be cancelled im-

mediately by pressing the button|3 .

WARNING! Risk of material

damage!

~ Observe the specified operating time of

the device. After the sealing or vacuum-

ing process, the device must cool down

for at least 80 seconds.

8.1 Fill the bag

CAUTION:

~ No food or liquids must be present at

the top edge, where you want to seal

the bag. That area must be clean and

dry. Otherwise, it is impossible to pro-

duce a proper welding seam.

• Fill the bag only up to a level of 6 cm

below the top edge.

8.2 Seal the bag

1. Smooth the bag where it is to be

sealed.

2. Open the lid|11. If necessary, press the

buttons|8 first.

3. Figure A: place the bag in the device.

For this purpose, the end of the film

must be positioned shortly in front of the

rear limitation webs|12 and the lateral

limitation webs|15.

4. Ensure again that there are no creases

in the film - especially in the area above

the welding wire|14.

5. Close the lid|11.

6. Figure B: use both hands to press firm-

ly on the edges of the lid|11. They must

engage audibly.

__CPE281169_Folienschweissgeraet_B7.book Seite 7 Montag, 19. September 2016 3:19 15

Ocjena

Više o ovom priručniku

Razumijemo da je lijepo imati papirnati priručnik za svoj SilverCrest IAN 281169 Stroj za vakuumiranje. Uvijek možete preuzeti priručnik s naše web stranice i sami ga ispisati. Ako želite imati originalni priručnik, preporučujemo da kontaktirate SilverCrest. Oni bi mogli osigurati originalni priručnik. Tražite li priručnik za svoj SilverCrest IAN 281169 Stroj za vakuumiranje na drugom jeziku? Odaberite željeni jezik na našoj početnoj stranici i potražite broj modela da vidite imamo li ga na raspolaganju.

Tehnički podaci

Svi priručnici za SilverCrest Strojevi za vakuumiranje
Više priručnika za Strojevi za vakuumiranje

Često postavljana pitanja o SilverCrest IAN 281169 Stroj za vakuumiranje

Naš tim za podršku pretražuje korisne informacije o proizvodu i odgovore na česta pitanja. Ako u častim pitanjima naiđete na netočne informacije, obratite nam se putem obrasca za kontakt.

Povezani proizvodi

Priručnik

SilverCrest IAN 96111 Stroj za vakuumiranje

Priručnik

SilverCrest IAN 288381 Stroj za vakuumiranje

Priručnik

SilverCrest IAN 277100 Stroj za vakuumiranje

Priručnik

SilverCrest IAN 295933 Stroj za vakuumiranje

Priručnik

SilverCrest IAN 304253 Stroj za vakuumiranje

Priručnik

SilverCrest SV 125 D1 Stroj za vakuumiranje

Priručnik

SilverCrest SFSGM 1.5 B2 Stroj za vakuumiranje

Priručnik

SilverCrest IAN 310994 Stroj za vakuumiranje

Povezane kategorije