Priručnik Kärcher G 7.180 Visokotlačni perač

Priručnik

English 11

3. Press the lever of the high-pressure gun for 30 sec-

onds.

The pressure remaining in the system is discharged.

4. Release the lever of the high-pressure gun.

5. Lock the lever of the high-pressure gun.

6. Disconnect the device from the water supply.

7. Set the power switch to "0/OFF".

Transport

몇 CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during transporta-

tion.

Manual transport

몇 WARNING

Spilt fuel

Ignited fuel

Transport the device in a horizontal position.

1. Pull the device via the transport handle.

Transport in vehicles

1. Drain the fuel tank.

2. Secure the device against slipping and tipping over

when transporting in vehicles.

3. Transport the device standing up.

Care and service

몇 WARNING

Inadvertently starting up device

Risk of injury

Remove the spark plug prior to all work on the device.

몇 CAUTION

Risk of burns from hot surfaces.

Allow the device to cool down prior to all work.

Clean the sieve in the water connection

ATTENTION

Damaged sieve in the water connection

Damage to the device through contaminated water

Check the sieve for damage before inserting it in the wa-

ter connection.

If necessary, clean the sieve in the water connection.

1. Remove the water connection coupling.

Illustration L

2. Remove the sieve.

3. Clean the sieve under running water.

4. Insert the sieve into the water connection.

5. Disconnect the water connection coupling.

Clean the detergent filter

Clean the detergent filter before longer periods of stor-

age.

1. Pull the detergent suction hose out of the detergent

tank.

Illustration M

2. Clean the filter under running water.

High-pressure pump maintenance

The high-pressure pump is maintenance-free.

Engine maintenance

For engine maintenance see original operating instruc-

tions of the engine.

Storage

몇 CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during storage.

Storing the device

ATTENTION

Damp environment

Corrosion

Only store the device indoors.

1. Place the device on a level surface.

2. Disconnect the spray lance from the high-pressure

gun.

3. Press the separation button on the high-pressure

gun and disconnect the high-pressure hose from the

high-pressure gun.

4. Press the casing of the high-pressure hose quick

coupling in the direction of the arrow and pull out the

high-pressure hose.

5. Stow the spray lance and high-pressure hose on the

device.

Observe the additional instructions before storing the

device for a longer period of time, see chapter Care and

service and original operating instructions of the engine.

Frost protection

ATTENTION

Danger of frost

Incompletely emptied devices can be destroyed by

frost.

Completely empty the device and accessories.

Protect the device from frost.

The following requirements must be satisfied:

 The device is disconnected from the water supply.

 The high-pressure hose is removed.

1. Switch on the device (see chapter High-pressure

operation).

2. Wait for a maximum of 1 minute until no more water

escapes from the high-pressure connection.

3. Switch off the device.

4. Store the device in a frost-protected room, together

with all accessories.

Troubleshooting guide

몇 WARNING

Inadvertently starting up device

Risk of injury

Remove the spark plug prior to all work on the device.

몇 CAUTION

Risk of burns from hot surfaces.

Allow the device to cool down prior to all work.

Motor not running

 See original operating instructions of the engine.

Device does not reach required pressure

The engine speed is too low.

1. Check the engine speed (see chapter Technical da-

ta).

The sieve in the water connection is dirty.

1. Empty and clean the sieve in the water connection

(see chapter Clean the sieve in the water connec-

tion).

Air is in the system.

1. Vent the device (see chapter Vent the device).

The water supply is too low.

1. Open the water tap fully.

2. Check the water inlet for an adequate flow rate.

3. Check that the maximum suction height is not ex-

ceeded (see Technical data).

The high-pressure pump piping is leaking or dirty.

1. Check the piping.

Ocjena

Više o ovom priručniku

Razumijemo da je lijepo imati papirnati priručnik za svoj Kärcher G 7.180 Visokotlačni perač. Uvijek možete preuzeti priručnik s naše web stranice i sami ga ispisati. Ako želite imati originalni priručnik, preporučujemo da kontaktirate Karcher. Oni bi mogli osigurati originalni priručnik. Tražite li priručnik za svoj Kärcher G 7.180 Visokotlačni perač na drugom jeziku? Odaberite željeni jezik na našoj početnoj stranici i potražite broj modela da vidite imamo li ga na raspolaganju.

Tehnički podaci

Svi priručnici za Kärcher Visokotlačni perači
Više priručnika za Visokotlačni perači

Često postavljana pitanja o Kärcher G 7.180 Visokotlačni perač

Naš tim za podršku pretražuje korisne informacije o proizvodu i odgovore na česta pitanja. Ako u častim pitanjima naiđete na netočne informacije, obratite nam se putem obrasca za kontakt.

Povezani proizvodi

Priručnik

Kärcher HD 6/13 CX Visokotlačni perač

Priručnik

Kärcher HDS 8/18-4 CX Visokotlačni perač

Priručnik

Kärcher K 4.800 Ecologic Visokotlačni perač

Priručnik

Kärcher K 5 Premium Smart Control Visokotlačni perač

Priručnik

Kärcher K 4.97 M Visokotlačni perač

Priručnik

Kärcher HD 6/12-4 CX Visokotlačni perač

Priručnik

Kärcher K 7 Compact Visokotlačni perač

Priručnik

Kärcher HDS 8/18-4 C Visokotlačni perač

Povezane kategorije